Tig Welding Technics Manual

Posted on by admin

Tip tig wp 18 sc torch and connections 30 - 31 tip tig interconnection cable and ground 32 tip tig electronics and power 33 - 40 tip tig warranty 41 wp18 sc large configuration 42 wp18 sc medium configuration 43 wp18 sc torch instructions 44 - 48 welding techniques 49 - 57.

What is a good setting of the pulse parameters for tig welding equipment?

Before I ramble on about Tig Welding Equipment Pulse settings, if you dont want to read it, here are some good pulse settings I have found work on certain things.

Tig Welding Technics Manual Online

Welding near an edge on .125' 308 stainless steel

Tig welding for beginners pdf

50 pps

30% on time

30% background

Weld build up on the edge of .050' steel, stainless, or nickel alloy

Using manual TIG welding equipment SEMPEO1-16 Using manual TIG welding equipment 6 Additional Information. Scope/range related to performance criteria. You must be able to: 1. Prepare for the manual TIG welding process, to include carrying out. Of the following: 1.1 adhere to procedures or systems in place for risk assessment. (This is a two-part document, with general tig welding first followed by one aluminum-specific.)TIG WELDING TIPSbyTom Bell1. The bigger the rod, the easier it is to feed. Use larger diameter rods (3/32” to 1/8”) when learning if possible.2. Rod angle and torch angle should not be the same because the heat will bounce off of yourpart and melt the rod before you want it to. TIG WELDING CURRENT CONTROL: With the TIG welding process it's especially important to control the current during the TIG 'arc start' and at the 'arc end.' In a manual TIG welding application, the welder may use a variable amp control which he or she regulates through a foot current control. DC welding aluminum has a different feel than AC welding, and it’s not easy to get a bead to with the “stack of dimes” look of good TIG welding. A little practice will help you get a feel for the weld and go a long way to a pretty weld on your finished product.

30 pps

20 % on time

20 percent background

Build up of threads on a 1 inch thick 4340 shaft

150 pps

50 % on time

50 % background

There are other settings that would have worked too but I thought I might just list a few so that you would have some good places to start on certain jobs.

Every tig welding machine is slightly different but the concepts are basically the same.There are 4 basic settings to understand:

1. Main Amperage - if you are using a foot pedal, you will vary the main amperage but remember this tip...You will need to set the main amperage at roughly twice the amperage you would select without pulse because with pulse, you get an average of the high and the low...roughly.

2. pulse frequency in pulses per second or pps - I like to either weld at about 1 pps, or above 20....preferable above 30.

3. Pulse Time on in % also known as pulse width - This is the percentage of time the current stays on the high side of the pulse. For starters, I recommend 30-50 percent...if you go much lower than 30, it just limits your heat too much and you wind up just giving it more foot pedal to compensate.

4. background current - Background current is the low current of the pulse. This is not the percentage of time but a percentage of the high pulse amperage. On some machines it is just the exact background amperage but either way, The lower you set it, the more pulse effect...to an extent. Just like the pulse time on, if you go too low with this setting, it just limits the output of the machine too much...I recommend setting it at 20-50 for starters.

The Everlast Powertig 250EX setting for background current is called pulse amps ratio...so if you set the main amps at 100 and the pusle amps ratio at 20%, your high pulse is 100 and the background current is 20 amps.

Older transformer style welders can only manage about 10 pulses per second. If you have ever had to weld at 10 pps, you know what I know. It sucks.

I would rather get kicked in the stones than to have to weld all day at 10 pps.

But newer inverter tig welding equipment like the Everlast Powertig 250 Ex in this video is capable of 500pps.

Where do you need 500 pulses per second? You probably dont .

High pulse rates like 500 sing at a high pitch and make you want some earplugs. The arc stiffens but as far as controlling heat, it does not offer much benefit.

But pulse rates of around 100-150 have a really nice effect on the arc. The arc is stiffened just enough to want to stay where you put it, more focused, and wanders less ...it sticks where you put it and when you are welding next to an edge or corner, it really helps keep the heat from wandering to the edge.

In fact any pulse rate between 30 and 150 helps make the puddle stay put, in my opinion.

Here are some things I have observed about pulse.... pulse rates of 30-40 agitate the puddle and let you move the puddle at a slightly lower average amperage than without pulse....

Pulse rates of from 50-150 really stiffen the arc and let you pinpoint the arc more than without pulse.

Pulse rates of around 1 pps limit heat input the most and prevent heat buildup in the part being welded.

and one more thing...pulse tig really shines on automated welding applications much more so than manual welding with a foot pedal.

Travel speed and amperage adjusted by the welder will often negate a lot of the benefits of pulse tig welding equipment.

Tig welding how to

More tips for Controlling heat input and distortion using Pulse Tig on Stainless Steel

• Dont fart around...get in, get to welding, get out.

• Use as small a tungsten as practical and keep it sharp and clean.

• Set your tig welding equipment to the lowest amperage that is practical. I am not talking about using such a low amperage that the weld takes forever to get a puddle…just use enough to where you can get the puddle going within a second or two and then get moving, but dont use more than is needed .

• Use the smallest filler rod that is practical. If dipping the rod in the puddle seems to suck all the heat out of the puddle, use a smaller rod.

• If distortion is your main problem, Weld in short stitches wherever possible.

• Back-purge your welds with argon…if you don’t, pulsing will not have much benefit.

Tig welding for beginners

How To Start Tig Welding

• A good pulse setting For controlling heat input is setting the percent on time and background current to around 20 each.

• Make sure you get a, tight, tight joint fit-up.

Tig Welding Guide Pdf

• Clamp everything as solid as possible to heavy pieces of aluminum or copper, if possible.

Tig Welding Technics Manual Pdf

• Use 308LSI wire when possible, the added Silicon lowers the melting point a little bit and makes the puddle wet better.
see more on tig welding equipment inverter settings
Part 2 of tig welding inverter settings
part 3 tig welding equipment inverter settings